IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx INE 14.0037X issue No.: 0
 
Status:
Current
 
Date of Issue:2015-02-12Page 1 of 3
 
 
Applicant:
OFFICINE MECCANICHE M.A.M
Via Vico Veneto, 32
I - 20090 Fizzonasco di Pieve Emanuele (MI)
Italy
Equipment:Enclosures type EJB...
 
Optional accessory:
 
Type of Protection:d, d [ia], tb [ia]

 Marking:

Ex d IIB+H2 T6...T4 Gb
Ex d [ia IIA or IIB or IIC Ga] IIB+H2 T6...T4 Gb
Ex d I Mb
Ex d [ia Ma] I Mb
Ex tb III C T85°C...T135°C Db IP66
Ex tb [ia Da] III C T85°C...T135°C Db IP66

 
 
Approved for issue on behalf of the IECEx
Certification Body:
Thierry HOUEIX

 
Position:Ex Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
INERIS
Institut National de l'Environnement Industriel
et des Risques
BP n2
Parc Technologique ALATA
F-60550 Verneuil-En-Halatte
France


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx INE 14.0037X
 
Date of Issue:2015-02-12Issue No.: 0
 
Page 2 of 3
  
Manufacturer:
OFFICINE MECCANICHE M.A.M
Via Vico Veneto, 32
I - 20090 Fizzonasco di Pieve Emanuele (MI)
Italy


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-1 : 2007-04
Edition: 6
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 60079-11 : 2011
Edition: 6.0
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-31 : 2013
Edition: 2
Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

FR/INE/ExTR14.0072/00


Quality Assessment Report:

FR/INE/QAR11.0004/03


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx INE 14.0037X
 
Date of Issue:2015-02-12Issue No.: 0
 
Page 3 of 3
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The enclosures type EJB... use the flameproof enclosure certified as Ex Component covered by IECEx INE 14.0036U.

They can be fitted with operator covered by IECEx INE 14.0032U and a breathing or draining device covered by IECEx INE 12.0002U.

These enclosures are intended to contain mainly electrical and/or electronical "NIS" components, they can also contain "IS" elements covered by a separated IECEx certificate.

These enclosures get the degrees of protection IP66 in accordance with IEC 60529 standard.

 



 SPECIFIC CONDITIONS OF USE:   YES as shown below:
 
 

 - The  gap of different joins is lower to those specified in tables of IEC 60079-1.
 - The width of the flameproof joints is superior to those specified in tables of IEC 60079-1.
 - For used in group I, during the installation, the user will take into consideration that the enclosures underwent only a shock corresponding to an energy of a low risk.

 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.