Certificate of Conformity: IECEx BAS 10.0103X


		IECEx Certificate of Conformity


	INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com UNIT VERIFICATION


	Certificate No.:	IECEx BAS 10.0103X issue No.:2 Certificate history: Issue No. 3 (2012-11-23) Issue No. 2 (2011-12-1) Issue No. 1 (2011-9-21) Issue No. 0 (2010-12-7)

	Status:	Current

	Date of Issue:	2011-12-01		Page 1 of 4

	Applicant:

		Druck Limited Fir Tree Lane Groby Leicestershire LE6 0FH United Kingdom

	Electrical Apparatus:	UNIK 5000 Pressure Sensor

	Optional accessory:



	Type of Protection:	Intrinsic safety

	Marking:	Ex ia I Ma (-40�C ≤ Ta ≤ +80�C) Ex ia IIC T5 Ga (-40�C ≤ Ta ≤ +80�C)


	Approved for issue on behalf of the IECEx Certification Body:		R S Sinclair

	Position:		Managing Director

	Signature: (for printed version)

	Date:


	1. This certificate and schedule may only be reproduced in full. 2. This certificate is not transferable and remains the property of the issuing body. 3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.


Certificate issued by:

	Baseefa Rockhead Business Park Staden Lane Buxton Derbyshire SK17 9RZ United Kingdom


		IECEx Certificate of Conformity


Certificate No.:	IECEx BAS 10.0103X

Date of Issue:	2011-12-01	Issue No.: 2

		Page 2 of 4

Manufacturer:

Druck Limited
Fir Tree Lane
Groby
Leicestershire
LE6 0FH
United Kingdom

Additional Manufacturing location(s):

G.E. Industrial Sensing (Changzhou) Co Ltd
Building 10, Jintong International Ind Park
No 8 Xihu Road
Wujin High-Tech Industrial Zone
Changzhou, Jiangsu
China 213164
China

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.

STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

IEC 60079-0 : 2004 Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-0 : 2007-10 Edition: 5		Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-11 : 2006 Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"

This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.

TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

Test Report:

GB/BAS/ExTR10.0224/02

Quality Assessment Report:

GB/BAS/QAR06.0059/03

GB/BAS/QAR07.0044/02


		IECEx Certificate of Conformity


Certificate No.:	IECEx BAS 10.0103X

Date of Issue:	2011-12-01	Issue No.: 2

		Page 3 of 4

Schedule

EQUIPMENT:

Equipment and systems covered by this certificate are as follows:

The UNIK5000 Pressure Sensor is designed to measure the pressure of a process fluid and output an electrical signal proportional to the pressure applied. There are three main product variants in the series; PMP; PDCR; and PTX; each with a range of different electrical connection and electrical output signal options.

The main body of the pressure sensor is made from stainless steel and/or Hastelloy. Some variants may be fitted with an optional depth cone to protect the diaphragm of the pressure sensing element. Within the enclosure, the conditioning electronics are partially encapsulated. Gauge versions are provided with a vent that is either via a vent tube within the integral cable; vents into the mating connector; or vents from the body of the enclosure via a PTFE filter port.

Electrical connections are either made via an integral cable or a connector.

CONDITIONS OF CERTIFICATION: YES as shown below:

1. Do not rub non-metallic parts with a dry cloth or install in a high velocity dust laden atmosphere.

2. PMP versions will not pass the 500Vrms dielectric strength test and so this must be taken into account during installation.


		IECEx Certificate of Conformity


Certificate No.:	IECEx BAS 10.0103X

Date of Issue:	2011-12-01	Issue No.: 2

		Page 3 of 4

EQUIPMENT(continued):


		IECEx Certificate of Conformity


Certificate No.:	IECEx BAS 10.0103X

Date of Issue:	2011-12-01	Issue No.: 2

		Page 4 of 4

DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):

Variation 2.1

To update the QAR and ExTR references. No other changes have been made.

ExTR: GB/BAS/ExTR10.0224/02

File Reference: 11/0965


		IECEx Certificate of Conformity


Certificate No.:	IECEx BAS 10.0103X

Date of Issue:	2011-12-01	Issue No.: 2

		Page 4 of 4

Additional information:

iecex.iec.ch:

Home / Search
Certified Service Facilities
Conformity Mark Licenses
Certified Persons


View by:

"All ExCBs" Certificates
Certificate ref. number
IECEx Cert. Body (ExCB)
Applicant
Applicant Location
Manufacturer location
Country/Standards/ExCBs
Standard used
ExTRs
QARs

Services:

Export to MS Excel
Operational Manual

Loading...

iecex.iec.ch::CoC online home