IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx ULD 10.0019X issue No.:1
 
Status:
Current
 
Date of Issue:2012-01-12 Page 1 of 6


    
Applicant:
Detector Electronics Corporation
6901 West 110th Street
Minneapolis, MN 55438
United States of America


 
Electrical Apparatus:DuctWatch Gas Monitor, Model PIRDUCT
Optional accessory:


 
Type of Protection:Flameproof enclosure 'd'


 
Marking: Ex d IIB+H2 T4-T6 Gb IP66
 
Approved for issue on behalf of the IECEx
Certification Body:		Jasmin Omerovic

 
Position:Certification Project Engineer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
UL International DEMKO A/S
Borupvang 5A,
DK-2750 Ballerup
Denmark


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx ULD 10.0019X
 
Date of Issue:2012-01-12Issue No.: 1
 
Page 2 of 6
 
 Manufacturer:
Detector Electronics Corporation
6901 West 110th Street
Minneapolis, MN 55438
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2007-10
Edition: 5		Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-1 : 2007-04
Edition: 6		Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
DK/ULD/ExTR10.0021/00DK/ULD/ExTR10.0021/01


Quality Assessment Report:

DK/ULD/QAR06.0002/02


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx ULD 10.0019X
 
Date of Issue:2012-01-12Issue No.: 1
 
Page 3 of 6
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 
The DuctWatch Gas Monitor, Model PIRDUCT, is used for the detection of combustible hydrocarbon gases in air handling ductwork and combustion turbine enclosure applications. The device electronics are housed in a cylindrical enclosure in type of explosion protection flameproof enclosure 'd' manufactured from aluminum and stainless steel.  
 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

The DuctWatch Gas Monitor, Model PIRDUCT has a threaded wire feed through incorporating flying leads. This feed through is to be screwed into the cable entry opening of a suitable certified (Ex 'd' or Ex 'e') enclosure in which the flying leads are to be terminated.

In order to maintain the Ingress Protection rating IP66, the back end of the DuctWatch Gas Monitor, Model PIRDUCT with the flying leads is to be screwed into a suitable certified flameproof enclosure with an Ingress Protection rating of at least IP66.

The captive front end screws are to be tightened with 1 Nm.

 

 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx ULD 10.0019X
 
Date of Issue:2012-01-12Issue No.: 1
 
Page 4 of 6
 
 
EQUIPMENT(continued):
 

For further details please see annex.

 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx ULD 10.0019X
 
Date of Issue:2012-01-12Issue No.: 1
 
Page 5 of 6
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 

Adding optional clamp, shim and optional EMI filterboard construction and upgrade IEC 60079-0 4th. edition to IEC 60079-0 5th. edition.

 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx ULD 10.0019X
 
Date of Issue:2012-01-12Issue No.: 1
 
Page 6 of 6
 
 
Additional information:
 

For further details please see annex.

 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.