IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx UL 06.0011U issue No.:1
 
Status:
Current
 
Date of Issue:2012-05-18 Page 1 of 4


    
Applicant:
Baseline-Mocon Inc.
19661 Highway 36
Lyons, CO 80540
United States of America


 
Electrical Apparatus:Type piD-TECH Sensor Plus, Part No. ZPP60180** Photo Ionization Detector
Optional accessory:


 
Type of Protection:ia


 
Marking:

Ex ia IIC Tamb = -20C to +60C

 

 
Approved for issue on behalf of the IECEx
Certification Body:		Paul T. Kelly

 
Position:Principal Engineer, Global Hazardous Locations


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
UL LLC
333 Pfingsten Road
Northbrook IL 60062-2096
United States of America


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx UL 06.0011U
 
Date of Issue:2012-05-18Issue No.: 1
 
Page 2 of 4
 
 Manufacturer:
Baseline-Mocon Inc.
19661 Highway 36
Lyons, CO 80540
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0		Explosive atmospheres - Part 0: General requirements
IEC 60079-11 : 2011
Edition: 6.0		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-26 : 2006
Edition: 2		Explosive atmospheres - Part 26: Equipment with equipment protection level (EPL) Ga
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
US/UL/ExTR06.0035/00US/UL/ExTR06.0035/01


Quality Assessment Report:

US/UL/QAR06.0001/05


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx UL 06.0011U
 
Date of Issue:2012-05-18Issue No.: 1
 
Page 3 of 4
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The Type piD-TECH Sensor Plus is a component photo ionization detector which is installed in an intrinsically safe gas detection instrument. The PID sensor is assigned intrinsically safe parameters which are provided on control drawing 7400-0108-011. The PID sensor receives intrinsically safe power from the unspecified gas detection instrument. All components are inside the plastic housing and are encapsulated except for the lamp, the LED and the detector cell. Three connecting pin are provided at the base of the sensor for installation. The two asterisks at the end of the part number are digits between 00 and 99 which represent the factory preset sensitivity range.

Schedule of Limitations: 1) The PID shall be installed inside of a suitable enclosure in accordance with the end product standard(s). 2) The PID was evaluated for a temperature classification of T4 when used in ambient temperatures up to +60 C. 3) The PID is to be powered from a intrinsically safe circuit. 4) The PID shall be used within the intrinsically safe ratings provided below. 5) Refer to control drawing 7400-0108-011 for details.

Connecting Pins

Note 2

Ui, V

 

Ii, A 

 

Pi, W

 

Ci, uF

 

Li, H

Pins:

J1, J2, J3

10.0

 

N/A

Note 1

 

N/A

Note 1

 

0

0

 

 

 

 

 

 

 

 

 

Note 1: Self limiting. Note 2: Refer to control drawing 7400-0108-011 for details.
 
CONDITIONS OF CERTIFICATION: NO
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx UL 06.0011U
 
Date of Issue:2012-05-18Issue No.: 1
 
Page 4 of 4
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 

The manufacturer requested the standards associated with this certificate be updated.

 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.