IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx KIWA 15.0017X issue No.: 1
 
Status:
Current
 
Date of Issue:2018-12-05Page 1 of 5
 
 
Applicant:
Pepperl+Fuchs GmbH
Lilienthalstraße 200
68307 Mannheim
Germany
Equipment:SMART Transmitter Power Supply Model HiC2025 and SMART Current Driver Model HiC2031
 
Optional accessory:
 
Type of Protection:Ex ec

 Marking:

Ex ec IIC T4 Gc

 
 
Approved for issue on behalf of the IECEx
Certification Body:
Pieter van Breugel

 
Position:Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
Kiwa Nederland B.V. (Unit Kiwa ExVision)
Wilmersdorf 50
7327 AC Apeldoorn
P.O. Box 137
The Netherlands


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx KIWA 15.0017X
 
Date of Issue:2018-12-05Issue No.: 1
 
Page 2 of 5
  
Manufacturer:
Pepperl+Fuchs GmbH
Lilienthalstraße 200
68307 Mannheim
Germany


 
Additional Manufacturing location(s):
Pepperl+Fuchs Asia Pte. Ltd.
18 Ayer Rajah Crescent
Singapore 139942
Singapore
PT. Pepperl+Fuchs Bintan
JI. Asoka SD 56
Bintan Industrial Estate
Lobam, Bintan Island
Indonesia

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-7 : 2015
Edition: 5.0
Explosive atmospheres – Part 7: Equipment protection by increased safety ''e''
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

NL/KIWA/ExTR15.0015/01


Quality Assessment Report:

DE/PTB/QAR06.0008/09


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx KIWA 15.0017X
 
Date of Issue:2018-12-05Issue No.: 1
 
Page 3 of 5
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

SMART Transmitter Power Supply Model HiC2025 is for the supply of intrinsically safe transmitters located in an explosive atmosphere and can also be used with an active intrinsically safe current source. It transfers the analog input signal to the non-intrinsically safe side as an isolated current signal.
Bi-directional communication is supported for transmitters that use current modulation to transmit data and voltage modulation to receive data.

SMART Current Driver Model HiC2031 repeats a 4 - 20 mA input signal from a non-intrinsically safe source to drive intrinsically safe HART I/P converters, valve actuators, and displays located in an explosive atmosphere.

The modules mount into a HiC Termination Board.

Ambient temperature range -20 ºC to +60 ºC.



 SPECIFIC CONDITIONS OF USE:   YES as shown below:
 
 

- The equipment shall only be used in an area of at least pollution degree 2, as defined in IEC 60664-1.

- The equipment shall be installed in an enclosure that provides a minimum ingress protection of IP54 in accordance with IEC 60079-0.

- Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment.

 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx KIWA 15.0017X
 
Date of Issue:2018-12-05Issue No.: 1
 
Page 4 of 5
 
 EQUIPMENT(continued):
 
 

Electrical data

Model HiC2025

Supply:
19 ... 30 V (via Termination Board),
rated current maximum 45 mA,
power maximum 1.1 W.

Output:
4 ... 20 mA or 1 ... 5 V on maximum 300 Ω (source mode) or
4 ... 20 mA, 15 … 26 Vdc (sink mode).

Model HiC2031

Supply:
19 ... 30 V (via Termination Board),
rated current maximum 30 mA,
power maximum 700 mW.

Input:
4 ... 20 mA (max. 30 mA),
maximum 27 V.

 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx KIWA 15.0017X
 
Date of Issue:2018-12-05Issue No.: 1
 
Page 5 of 5
 
 DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
 

Issue 1: Changed type of protection from “nA” to “ec”.

 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.