IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx IBE 10.0004X issue No.:1
 
Status:
Current
 
Date of Issue:2011-03-03 Page 1 of 4


    
Applicant:
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
Germany


 
Electrical Apparatus:Temperature Transducer MACX MCR-EX-T-UI(REL)-UP(-SP)
Optional accessory:


 
Type of Protection:Intrinsic Safety; Type 'n'


 
Marking: [Ex ia] IIC; [Ex iaD]; Ex nAC ic IIC T4 X
 
Approved for issue on behalf of the IECEx
Certification Body:		Prof. Dr. Tammo Redeker

 
Position:Head of Certification Body


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
IBExU Institut für Sicherheitstechnik GmbH
Certification Body
Fuchsmühlenweg 7
09599 Freiberg
Germany


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx IBE 10.0004X
 
Date of Issue:2011-03-03Issue No.: 1
 
Page 2 of 4
 
 Manufacturer:
PHOENIX CONTACT ELECTRONICS GmbH
Dringenauer Straße 30
31812 Bad Pyrmont
Germany


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-15 : 2005-03
Edition: 3		Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus
IEC 61241-0 : 2004
Edition: 1		Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
IEC 61241-11 : 2005
Edition: 1		Electrical apparatus for use in the presence of combustible dusts - Part 11: Protection by intrinsic safety 'iD'
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
DE/IBE/ExTR10.0005/00DE/IBE/ExTR10.0005/01


Quality Assessment Report:

NL/KEM/QAR06.0005/06


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx IBE 10.0004X
 
Date of Issue:2011-03-03Issue No.: 1
 
Page 3 of 4
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 
The temperature transducers MACX MCR-EX-T-UI(REL)-UP(-SP) are used for measuring temperatures by using different temperature sensing elements or low voltages up to 1000 mV in hazardous areas up to zone 0 and to transfer the measuring results as a normalized current or voltage signal into the safe area. Additional one or more switching contacts are available on the non intrinsically safe output side of the transducer. The intrinsically safe input circuit of the transducer is safe galvanically separated up to 375 Vpeak from the output and the supply circuit. The device is an associated apparatus having an input circuit of the protection type Intrisically Safety of category ia. The device may be operated in zone 2, if it is installed in a separate certified enclosure, which is suitable for this area (see General remarks).
A customized connector in the front of the module serves for special configuration or display tasks. This connection is energy limited in protection type ic and can be used in zone 2.

For module designation, technical data see the annex.
 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

Special conditions for safe use in zone 2:

1. The Temperature Transducer MACX MCR-EX-T-UI(REL)-UP(-SP) has to be installed in zone 2 within a certified enclosure fulfilling the requirements of IEC 60079-15 in protection category at least IP 54 according to IEC 60529. 
2. Connecting and disconnecting of not intrinsically safe circuits are not allowed in energized state of the Temperature Transducer MACX MCR-EX-T-UI(REL)-UP(-SP).
3. Only appropriate devices from PHOENIX CONTACT may be connected at the configuration interface in zone 2. 

 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx IBE 10.0004X
 
Date of Issue:2011-03-03Issue No.: 1
 
Page 4 of 4
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
The module designation was extended.
The layout has been modified slightly.
The values of some devices have been changed.
 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.