IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
Ex COMPONENT CERTIFICATE

 
Certificate No.:
IECEx SIR 07.0111U issue No.: 5
 
Status:
Current
 
Date of Issue:2018-08-28Page 1 of 4
 
 
Applicant:
International Metal Engineering Pte Limited
Blk 13 Toa Payoh Lorong 8
#06-05 Braddell Tech Park
Singapore 319261
Singapore
Ex Component: 8080, 8075, 8066 & 7080 Series Junction Boxes
This component is NOT intended to be used alone and requires additional consideration when incorporated into other equipment or systems for
use in explosive atmospheres (refer to IEC 60079-0).
 
 
Type of Protection:Flameproof and Dust

 Marking:

Stainless Steel Only
Ex db I Mb
Stainless Steel or Aluminium
Ex db IIC Gb
Ex tb III C Db IP68

Ta = -40°C to +85°C

 
 
Approved for issue on behalf of the IECEx
Certification Body:
C Ellaby

 
Position:Deputy Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
SIRA Certification Service
CSA Group
Unit 6, Hawarden Industrial Park
Hawarden, Deeside, CH5 3US
United Kingdom


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2018-08-28Issue No.: 5
 
Page 2 of 4
  
Manufacturer:
International Metal Engineering Pte Limited
Blk 13 Toa Payoh Lorong 8
#06-05 Braddell Tech Park
Singapore 319261
Singapore


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex Component covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The Ex Component and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-1 : 2014-06
Edition: 7.0
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 60079-31 : 2013
Edition: 2
Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the Ex Component listed has successfully met the examination and test requirements as recorded in

 
Test Report:

GB/SIR/ExTR08.0035/00GB/SIR/ExTR08.0166/00GB/SIR/ExTR09.0142/00GB/SIR/ExTR12.0243/00GB/SIR/ExTR18.0014/00GB/SIR/ExTR18.0150/00


Quality Assessment Report:

GB/SIR/QAR07.0040/00


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2018-08-28Issue No.: 5
 
Page 3 of 4
 
Schedule
 
   Ex Component(s) covered by this certificate is described below:
 

The 8080, 8075, 8066 and 7080 Series Instrument Enclosures are cylindrical single compartment enclosures comprising a base and cover with a maximum internal volume of 280 cm³. The enclosures are manufactured from cast aluminium or stainless steel. Some cast aluminium versions are painted with epoxy paint. The cover may be blank or have a window fitted. Each enclosure may have a number of conduit openings and sizes.  Refer to the Annexe for additional information, Schedule of Limitations and Condition of Manufacture.

 
 
   SCHEDULE OF LIMITATIONS:
 

Refer to the Annexe.

 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2018-08-28Issue No.: 5
 
Page 4 of 4
 
 DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
 

This issue recognises the following changes; refer to the certificate annex for a comprehensive history:

  1. The existing range was extended to include IME Model 7080TF* Junction Box (* denotes that an adhesive metric label is required when a metric thread is selected), made of stainless steel with blind cover. Marked suitable for concept of protections Ex db I Mb, or Ex db IIC Gb and Ex tb IIIC Db. The design is based upon model 7080TT* (stainless steel model with blind cover) with the following design differences only:
    a) Absence of the four external blind holes and their associated internal lugs on the interior of the cover they are machined into. Used to locate hammer driven rivets to mount certification labels.
    b) A reduction in height of the four, internal mounting lugs within the enclosure main body for internal circuitry.
 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.