IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx SIR 07.0111U issue No.: 0
 
Status:
Current
 
Date of Issue:2008-04-17Page 1 of 4
 
 
Applicant:
International Metal Engineering Pte Limited
Blk 13 Toa Payoh Lorong 8
#06-05 Braddell Tech Park
Singapore 319261
Singapore
Equipment:8080, 8075 and 7080 Series Instrument Enclosures and Junction Boxes
 
Optional accessory:
 
Type of Protection:Flameproof and Dust

 Marking: Ex d I or
Ex d II C T6 IP 68
Ex A21 tD T85 °C
 
 
Approved for issue on behalf of the IECEx
Certification Body:
D R Stubbings BA MIET

 
Position:Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
SIRA Certification Service
Rake Lane
Eccleston
Chester
CH4 9JN
United Kingdom


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2008-04-17Issue No.: 0
 
Page 2 of 4
  
Manufacturer:
International Metal Engineering Pte Limited
Blk 13 Toa Payoh Lorong 8
#06-05 Braddell Tech Park
Singapore 319261
Singapore


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2007-04
Edition: 6
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 61241-0 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
IEC 61241-1 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

GB/SIR/ExTR08.0035/00


Quality Assessment Report:

GB/SIR/QAR07.0040/00


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2008-04-17Issue No.: 0
 
Page 3 of 4
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 
The 8080, 8075 and 7080 Series Instrument Enclosures are cylindrical single compartment enclosures comprising a base and cover with a maximum internal volume of 280 cm³. The enclosures are manufactured from cast aluminium or stainless steel. Some cast aluminium versions are painted with epoxy paint. The cover may be blank or have a window fitted. Each enclosure may have a number of conduit openings and sizes. See table below: -

Model Range

No. of entriesSize of thread entries
½” NPT¾” NPT½” BSPM16 x 2(not a thru hole)M20 x 1.5None
80803XXXXXX
80753XXXXXX
70801XXX XX
70802 @ 90°XXX XX
70802 @ 180°XXX XX
70803XXX XX
70804XXX XX


 SPECIFIC CONDITIONS OF USE:   NO
 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 07.0111U
 
Date of Issue:2008-04-17Issue No.: 0
 
Page 4 of 4
 
 EQUIPMENT(continued):
 
 

Design Options

 

Model No

Model NoModel No

Description

8080 AT8075 ATIME 7080 AT  IME 7080 NTmade of cast aluminium with blind cover.
* 8080 AM* 8075 AM*IME 7080 AM* IME 7080 NMmade of cast aluminium with blind cover.
8080 WT8075 WTIME 7080 WT  IME 7080 CTmade of cast aluminium with glass window cover.
* 8080 WM* 8075 WM*IME 7080 WM*  IME 7080 CMmade of cast aluminium with glass window cover
8080 TT8075 TTIME 7080 TTmade of stainless steel with blind cover.
* 8080 TM* 8075 TM*IME 7080 TMmade of stainless steel with blind cover.
8080 ST8075 STIME 7080 STmade of stainless steel with glass window cover.
* 8080 SM* 8075 SM*IME 7080 SMmade of stainless steel with glass window cover.
 
The 7080WT, 7080WM, 7080AT and 7080AM are painted with an epoxy paint where the 7080CT, 7080CM, 7080NM and 7080NT are not painted.
 
Models with an asterisk (*) denote that an adhesive metric label is required when a metric thread is selected.

 

Conditions of Manufacture.

 

The 8080, 8075 and 7080 Series Instrument Enclosures and Junction Boxes, which are made from cast aluminium and fitted with a window assembly, shall be subjected to a routine overpressure test of 17.2 bar for at least 10 s as required by clause 16 of IEC 60079-1. There shall be no leakage, permanent deformation or damage.

 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.