IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx FMG 07.0006X issue No.:10
 
Status:
Current
 
Date of Issue:2012-02-02 Page 1 of 5


    
Applicant:
Mine Safety Appliances
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
United States of America


 
Electrical Apparatus:Ultima X Series Controller, Ultima XE Sensor, Ultima XI Sensor, Ultima XIR Sensor
Optional accessory:Refer to Equipment section of this certificate.


 
Type of Protection:Construction, Test and Marking of type of protection "d", "n", "ia" and "[ib]"


 
Marking: Refer to annex.
 
Approved for issue on behalf of the IECEx
Certification Body:		J.E.Marquedant

 
Position:Group Manager, Electrical


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
FM Approvals LLC
1151 Boston-Providence Turnpike
Norwood, MA 02062
United States of America


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2012-02-02Issue No.: 10
 
Page 2 of 5
 
 Manufacturer:
Mine Safety Appliances
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5		Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosure 'd'
IEC 60079-11 : 2006
Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-15 : 2005-03
Edition: 3		Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus
IEC 60079-29-1 : 2007
Edition: 1		Explosive Atmospheres - Part 29-1: Gas Detectors - Performance requirements of detectors for flammable gases
IEC 61779-1 : 1998
Edition: 1		Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods
IEC 61779-4 : 1998
Edition: 1		Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating up to 100% lower explosive limit
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
US/FMG/ExTR07.0004/00US/FMG/ExTR07.0011/00US/FMG/ExTR08.0007/00US/FMG/ExTR08.0007/01US/FMG/ExTR08.0009/00US/FMG/ExTR08.0009/06US/FMG/ExTR08.0009/08US/FMG/ExTR08.0009/09US/FMG/ExTR08.0009/10


Quality Assessment Report:

FR/INE/QAR08.0011/01


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2012-02-02Issue No.: 10
 
Page 3 of 5
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

Controllers: Ultima XL, Ultima XE Main

 

Sensors: Ultima XE Sensor, Ultima XI Sensor, Ultima XIR Sensor

 

Accessories: Ultima Calibrator, Ultima Controller, Ultima XE Sensor Weather/Wind/Sensor Guard P/N 10028904, Ultima XI and Ultima XIR Environmental Guard P/N 10041265, Ultima X Power Supply, HART Module

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 
 1)      Upon installation of the Ultima XL Control Unit, the label shall be permanently marked to show the type of explosion protection used for the installation. 2)  The Ultima X Control Unit complies with IEC 61779-1 and IEC 61779-4 when connected to a Detector Head that also has been evaluated to IEC 61779-1 and IEC 61779-4.3)  The Ultima XE Sensor, Ultima XI Sensor, and Ultima XIR Sensor complies with IEC 61779-1 and IEC 61779-4 when connected to a Control Unit that also has been evaluated to IEC 61779-1 and IEC 61779-4.4)  The Ultima XI Sensor and Ultima XIR Sensor comply with IEC 60079-29-1 when connected to a Control Unit that also has been evaluated to IEC 60079-29-1. 5)  The Ultima XI Sensor shall be connected directly to a junction box or instrument suitable for the area of installation to provide protection for the flying leads.6)  The Ultima XE Sensor and the Ultima XIR Sensor shall be connected directly to an Ultima X Series Control Unit or remote junction box.
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2012-02-02Issue No.: 10
 
Page 4 of 5
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
New O-ring from the same manufacturer.
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2012-02-02Issue No.: 10
 
Page 5 of 5
 
 
Additional information:
 

Annex: IECEx FMG 07.0006X provides marking information.

 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.