IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx SIM 11.0003 issue No.:0
 
Status:
Current
 
Date of Issue:2011-07-27 Page 1 of 4


    
Applicant:
MCE Lasers
17-19 Killara Road
Campbellfield VIC 3061
Australia


 
Equipment:Tunnel Laser Type LD.60.IS
Optional accessory:


 
Type of Protection:ia


 
Marking:

Ex ia I/IIC T4 IP55
IECEx SIM 11.0003

 
Approved for issue on behalf of the IECEx
Certification Body:
Ashraf Chowdhury

 
Position:Principal Engineer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 11.0003
 
Date of Issue:2011-07-27Issue No.: 0
 
Page 2 of 4
 
 Manufacturer:
MCE Lasers
17-19 Killara Road
Campbellfield VIC 3061
Australia


 
 Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
AU/SIM/ExTR11.0003/00


Quality Assessment Report:

AU/SIM/QAR11.0001/00


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 11.0003
 
Date of Issue:2011-07-27Issue No.: 0
 
Page 3 of 4
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

NOTE: This Certificate was originally suspended on 1st September 2016 at the request of the issuing IECEx Certification Body (ExCB) and subsequently reinstated on 3rd August 2017Products produced or installed prior to 1st September 2016 or after 3rd August 2017 are NOT affected by this suspension. Any comments or questions may be directed to the ExCB.

 The Tunnel Laser, Type LD.60.IS, is a laser diode equipment used in accurate construction and alignment of tunnels.

The device comprises a 2 mm thick stainless steel cylinder enclosure, which houses the electronics & four D-size batteries (Panasonic LR20GW). The cylindrical enclosure measures approximately 455 mm in length and 60 mm in diameter. The front glass holder and threaded battery end cap are located at opposing ends of the cylinder. The end cap comprises a power switch and an internal battery spring to maintain contact pressure on the cells and the power switch. Both ends of the cylindrical enclosure are made of brass and protected by black rubber caps.

 
SPECIFIC CONDITIONS OF USE: NO
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 11.0003
 
Date of Issue:2011-07-27Issue No.: 0
 
Page 4 of 4
 
 
Additional information:
 

The batteries can only be removed or replaced in a non-hazardous area.

 
 








Copyright © IEC-IECEx 2017 , Geneva Switzerland. All rights reserved.