IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx SIM 13.0004 issue No.:0

Certificate history:

 
Status:
Suspended
 
Date of Issue:2013-03-07 Page 1 of 4


    
Applicant:
MCE Lasers
17-19 Killara Road
CAMPBELLFIELD VIC 3061
Australia


 
Equipment:Tunnel Lasers Types LD.25.IS, LD.35.IS and LD.35.ISG
Optional accessory:


 
Type of Protection:ia


 
Marking: Ex ia I/IIC T3 IP55 (LD.25.IS)
Ex ia I/IIC T3 IP55 (LD.35.IS / LD.35.ISG powered by Powercell PC14AU)
Ex ia I/IIC T4 IP55 (LD.35.IS / LD.35.ISG powered by Panasonic LR14XW)
IECEx SIM 13.0004
 
Approved for issue on behalf of the IECEx
Certification Body:
Ashraf Chowdhury

 
Position:Principal Engineer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 13.0004
 
Date of Issue:2013-03-07Issue No.: 0
 
Page 2 of 4
 
 Manufacturer:
MCE Lasers
17-19 Killara Road
CAMPBELLFIELD VIC 3061
Australia


 
 Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-11 : 2011
Edition: 6.0
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
AU/SIM/ExTR13.0002/00


Quality Assessment Report:

AU/SIM/QAR11.0001/02


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 13.0004
 
Date of Issue:2013-03-07Issue No.: 0
 
Page 3 of 4
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

NOTE: This Certificate is suspended from 1st September at the request of the issuing IECEx Certification Body (ExCB). Products produced or installed prior to this date are NOT affected by this suspension. Any comments or questions may be directed to the ExCB.

 

The Tunnel Laser is a portable alignment laser housed in a stainless steel cylindrical housing and is powered by two AA-size (LD.25.IS) or two C-size primary cell (LD.35.IS / LD.35.ISG). The laser light aperture and threaded battery end cap are located at opposing ends of the housing. The battery end-cap comprises an internal battery spring to maintain contact pressure on the cells and an external power button sealed by a rubber cap.  

Temperature classification and type of battery allowed for each model is as below.

Model Number

Battery

Temperature classification

LD.25.IS

AA-size primary cell Powercell type PC15AU

T3

LD.35.IS

C-size primary cell Powercell type PC14AU

T3

C-size primary cell Panasonic type LR14XW

T4

LD.35.ISG

C-size primary cell Powercell type PC14AU

T3

C-size primary cell Panasonic type LR14XW

T4

 
SPECIFIC CONDITIONS OF USE: NO
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx SIM 13.0004
 
Date of Issue:2013-03-07Issue No.: 0
 
Page 4 of 4
 
 
Additional information:
 

The batteries can only be removed or replaced in a non-hazardous area.

 
 








Copyright © IEC-IECEx 2017 , Geneva Switzerland. All rights reserved.