IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity

IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit

Certificate No.:
IECEx TUR 12.0005X issue No.: 0

Certificate history:

Date of Issue:2012-04-20Page 1 of 3
Fluidtechnik Fiedler GmbH
Walter-Welp-Strasse 9, 44149 Dortmund
Equipment:Controller-/ Terminal Box - Type: FTE ****
Optional accessory:
Type of Protection:Ex d - flameprrof; Ex e - increased safety; Ex i - intrinsic safety


see explanation in the attachment

Approved for issue on behalf of the IECEx
Certification Body:
Dipl.-Ing. Heinz Farke

Position:Deputy Head of ExCB

(for printed version)
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.

  Certificate issued by:
TUV Rheinland Industrie Service GmbH
Am Grauen Stein
51105 Cologne


IECEx Certificate
of Conformity

Certificate No.:IECEx TUR 12.0005X
Date of Issue:2012-04-20Issue No.: 0
Page 2 of 3
Fluidtechnik Fiedler GmbH
Walter-Welp-Strasse 9, 44149 Dortmund

Additional Manufacturing location(s):


This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.

The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

IEC 60079-0 : 2007-10
Edition: 5
Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-1 : 2007-04
Edition: 6
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-7 : 2006-07
Edition: 4
Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.

TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

Test Report:


Quality Assessment Report:



IECEx Certificate
of Conformity

Certificate No.:IECEx TUR 12.0005X
Date of Issue:2012-04-20Issue No.: 0
Page 3 of 3
Equipment and systems covered by this certificate are as follows

The control and terminal box type FTE is a modular system of certified enclosures, which can be equipped with additional terminals and components. The devices will be combined according to customer specified demands. Therefore an individual documentation for each assembly is available. 

The designations of additional components of combined devices are added to the designation label of the main device. 

Ex-certified or non-Ex-certified components can be mounted into these pressure proofed enclosures.Only terminals of the specified type of protection are allowed to be mounted into the terminal boxes.  

Only components which have a certification to be used within Ex-areas with the required category are allowed to be mounted into the control boxes.

The markings have to be completed by the type of protection of the inserted devices.  

The temperature class has to be derived for the actual assembly.


The requirements of IEC 60079-14 have to be considered due to the individual setup, wiring and installation.

The special conditions of the certified devices have to be considered and all essential information shall be inserted into the final user documentation.

Only certified cable glands, which are qualified to be used within the particular protection type of the enclosure, shall be used.


Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.