IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx PTB 16.0005 issue No.: 0

Certificate history:

 
Status:
Current
 
Date of Issue:2016-02-08Page 1 of 3
 
 
Applicant:
VELOMAT Messelektronik GmbH
Schwarzer Weg 23b
01917 Kamenz
Germany
Equipment:Load cell type SKA-30X-Y-1.Z0S ATEX
 
Optional accessory:
 
Type of Protection:General requirements, Intrinsic Safety

 Marking: Ex ib IIB T4 Gb
 
 
Approved for issue on behalf of the IECEx
Certification Body:
Dr.-Ing. Udo Gerlach

 
Position:Head of Working Group Ignition Hazards of Modern Energy Supply Systems


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
Physikalisch-Technische Bundesanstalt (PTB)
Bundesallee 100
38116 Braunschweig
Germany


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 16.0005
 
Date of Issue:2016-02-08Issue No.: 0
 
Page 2 of 3
  
Manufacturer:
VELOMAT Messelektronik GmbH
Schwarzer Weg 23b
01917 Kamenz
Germany


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-11 : 2011
Edition: 6.0
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

DE/PTB/ExTR16.0006/00


Quality Assessment Report:

DE/PTB/QAR12.0008/01


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 16.0005
 
Date of Issue:2016-02-08Issue No.: 0
 
Page 3 of 3
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The load cell types SKA-30X-Y-1.Z0S ATEX are used to measure forces in the hazardous area. There they are used among other things in tape scales, container scales, platform scales and hanging scales for measuring forces on machine parts, leers or shafts.

 

The permissible ambient temperature range is -15°C to +60°C.  

 

Electrical data

Supply and signal circuit            in type of protection Intrinsic Safety Ex ib IIB
                                                   Ui =  25,2
V
                                                   Ii =  125  
mA
                                                   Pi =    0,8   
W
                                                   Ci =    0,65 
µF
                                                   Li  negligible low



 SPECIFIC CONDITIONS OF USE:   NO
 
 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.