IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx LCI 10.0047X issue No.:0

Certificate history:

 
Status:
Current
 
Date of Issue:2010-12-20 Page 1 of 3


    
Applicant:
BENTLY NEVADA
1631 Bently Parkway South
Minden, NV 89423
United States of America


 
Electrical Apparatus:Accelerometer
Optional accessory:


 
Type of Protection:ia


 
Marking: BENTLY NEVADA
Address:…
Serial Number:…
Year of construction:…
Ex ia IIC T4
Tamb: -40°C to +80°C
IECEx LCI 10.0047X
Ui= 27V, Ii=150 mA, Pi= 880mW, Ci=16.2 nF, Li=0µH
 
Approved for issue on behalf of the IECEx
Certification Body:		Marc GILLAUX

 
Position:Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
Laboratoire Central des Industries Electriques (LCIE)
33 Avenue du General Leclerc
FR-92260 Fontenay-aux-Roses
France


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx LCI 10.0047X
 
Date of Issue:2010-12-20Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
PCB Piezotronics Inc.
3425 Walden Avenue
Depeuw, New York
14043 USA
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
FR/LCI/ExTR10.0052/00


Quality Assessment Report:

CA/CSA/QAR09.0018/00


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx LCI 10.0047X
 
Date of Issue:2010-12-20Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The equipment is an accelerometer, type: 20015X.

The accelerometers are constructed of stainless steel, and consist of a connector, a piezo-crystal assembly and various non-protective component mounted on a printed board circuit. All models use one metal enclosure to house both the piezo-crystal and the charge amplifier. The X in the type number may be a number from 1 to 9, which denotes a change in the front-end resistance values for filtering purposes.

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

Equipment has to be connected to an apparatus with intrinsic interface in accordance with following characteristics: Uo≤ 27V, Io≤150 mA, Po≤880mW

 

 







Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.