IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx INE 11.0013X issue No.:0
 
Status:
Current
 
Date of Issue:2011-09-16 Page 1 of 3


    
Applicant:
NUOVA ASP Srl
Via Gasperi, 26
I - 20090 Pantigliate
Italy


 
Electrical Apparatus:Cable glands type P** or P*R*
Optional accessory:


 
Type of Protection:d, e and tD


 
Marking: Ex d IIC, Ex e II, Ex tD A21 IP66 or IP66/68
 
Approved for issue on behalf of the IECEx
Certification Body:		Thierry HOUEIX

 
Position:Ex Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
INERIS
Institut National de l'Environnement Industriel
et des Risques
BP n2
Parc Technologique ALATA
F-60550 Verneuil-En-Halatte
France


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx INE 11.0013X
 
Date of Issue:2011-09-16Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
NUOVA ASP Srl
Via Gasperi, 26
I - 20090 Pantigliate
Italy


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5		Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosure 'd'
IEC 60079-7 : 2006-07
Edition: 4		Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
IEC 61241-0 : 2004
Edition: 1		Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
IEC 61241-1 : 2004
Edition: 1		Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
FR/INE/ExTR11.0014/00


Quality Assessment Report:

IT/CES/QAR06.0001/05


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx INE 11.0013X
 
Date of Issue:2011-09-16Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

This range of cable glands type  P*or P*R*  is protected by flameproof enclosure, increased safety and dust protection for sizes 1 up to 4 and protected only by increased safety and dust protection for size 0.
These cable entries are foreseen, in accordance with the type, for armoured cables or non armoured cables.
In accordance to the type, the cable gland can be realised with a simple sealing ring or double sealing ring.
The cable glands type P*R*.. are provided with a sealed bushing.
These cable glands gets the protection degrees IP66 or IP66/68 according to the  standard IEC 60 529 ; the verification of the protection degree IPX8 corresponds to an immersion under 10 meters of water during 6 hours.

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

The temperature of the enclosure, at the connection point of the cable entry must not exceed the following values :
For the type P** or P*R*:

  • 90°C with sealing ring in EPDM with or without sealing compound.
  • 180°C with sealing ring in SILICONE with or without sealing compound.

The minimum temperature for use is -40°C for sealing ring in EPDM and -60°C for sealing ring in silicone.

The user shall use cables with thermal stability in accordance with the temperature of the sealing ring.

The clamping of the cables, for the cable glands must be realized oustside of the enclosure, nearby to the enclosure on which the cable glands are installed.

In order to maintained the IPX8 the cable entry shall be fitted on enclosure which satisfies an immersion test under 10 meters of water during 6 hours.

 

 







Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.