IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx INE 09.0006X issue No.:0

Certificate history:

 
Status:
Current
 
Date of Issue:2009-10-12 Page 1 of 3


    
Applicant:
RAEL MOTORI ELETTRICI S.r.l.
Via per Retorto, 7/1
I -15077 Predosa (AL)
Italy


 
Electrical Apparatus:ASYNCHRONOUS MOTOR Model AD90 TS
Optional accessory:


 
Type of Protection:d


 
Marking: Ex d IIB T4 or T3
 
Approved for issue on behalf of the IECEx
Certification Body:		Thierry HOUEIX

 
Position:Ex Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
INERIS
Institut National de l'Environnement Industriel
et des Risques
BP n2
Parc Technologique ALATA
F-60550 Verneuil-En-Halatte
France


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx INE 09.0006X
 
Date of Issue:2009-10-12Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
RAEL MOTORI ELETTRICI S.r.l.
Via per Retorto, 7/1
I -15077 Predosa (AL)
Italy


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5		Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosure 'd'
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
FR/INE/ExTR09.0020/00


Quality Assessment Report:

IT/CES/QAR07.0003/02


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx INE 09.0006X
 
Date of Issue:2009-10-12Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

DESCRIPTION

The motor enclosure, made in light alloy, is fitted with a cable permanently and with two or three internal thermal probes put in winding.
 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

The screws used for the assembly of the various parts of explosion-proof enclosures must be in steel or stainless steel with quality higher or equal to 4.8.

The gap and diametrical clearances are less than the values specified in the table 1 of the standard EN 60079-1 and are specified on the instructions.

The user will have to connect the free extremity of cable either in a non-explosive atmosphere or in an enclosure protected by a recognised protection mode for the corresponding area.

 







Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.