IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx FME 10.0010U issue No.:1
 
Status:
Current
 
Date of Issue:2011-10-24 Page 1 of 5


    
Applicant:
Transistor Devices, Inc.(trading as TDI Power)
36 Newburgh Road
Hackettstown, NJ 07840
United States of America


 
Electrical Apparatus:Battery Charger Model SPS5711
Optional accessory:


 
Type of Protection:Type 'n'


 
Marking: Ex nA nC IIC
Ta = 0 °C to +60 °C
 
Approved for issue on behalf of the IECEx
Certification Body:		Andrew Was

 
Position:Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
FM Approvals Ltd
1 Windsor Dials
SL4 1RS Windsor
United Kingdom


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FME 10.0010U
 
Date of Issue:2011-10-24Issue No.: 1
 
Page 2 of 5
 
 Manufacturer:
Transistor Devices, Inc. (trading as TDI Power)
36 Newburgh Road
Hackettstown, NJ 07840
United States of America


 
 Additional Manufacturing location(s):
Transdev Electronics (Shenzhen)
Fl 4&5 Shenzhen Development Bank Information Technology Building,
No. 16 Shihua Road,
Futian Free Trade Zone,
Shenzhen
China
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-15 : 2005-03
Edition: 3		Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
GB/FME/ExTR10.0002/00GB/FME/ExTR10.0002/01


Quality Assessment Report:

GB/FME/QAR11.0005/00


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FME 10.0010U
 
Date of Issue:2011-10-24Issue No.: 1
 
Page 3 of 5
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The Battery Charger Model SPS5711 is a DC-DC battery charger with an analogue circuit. The DC-DC battery charger contains a cooling fan and is a bi-directional device charging the backup battery during normal operation and delivering 24-26 Vdc, 20 A from the backup battery to the load in the event of failure of the power supply. The enclosure is made of aluminium, and the front panel has two signal LEDs, two output voltage test points and an on/off switch. The electrical ratings are:

Input 24-26 Vdc, 20 A

Output 24-26 Vdc, 20 A

Battery port 30-43 Vdc, 20 A

 

 

 
CONDITIONS OF CERTIFICATION: NO
 

 

 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FME 10.0010U
 
Date of Issue:2011-10-24Issue No.: 1
 
Page 4 of 5
 
 
EQUIPMENT(continued):
 
Schedule of limitations 

1.   The equipment shall be mounted within a tool-secured enclosure which meets the requirements of EN 60079-0 and EN 60079-15 and is capable of accepting the applicable wiring methods specified in EN 60079-14.  Where installed in outdoor or potentially wet locations, the enclosure shall, at a minimum, meet the requirements of IP54.  Where installed in locations providing adequate protection against the entry of solid foreign objects or water capable of impairing safety, the enclosure shall, at a minimum, meet the requirements of IP4X.

2.   Only batteries and cells obtained from Transistor Devices Inc are acceptable.

 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx FME 10.0010U
 
Date of Issue:2011-10-24Issue No.: 1
 
Page 5 of 5
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
Correction to ExTR number
 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.