IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx LCI 10.0014X issue No.:0
 
Status:
Current
 
Date of Issue:2010-07-20 Page 1 of 3


    
Applicant:
VIBRO-METER SA
Route de Moncor 4
1701 FRIBOURG
Switzerland


 
Electrical Apparatus:Dynamic Pressure Sensor
Optional accessory:


 
Type of Protection:nA


 
Marking: VIBRO METER
Address : ...
Type : PNR : 143-21X-000-YYY
Serial number : …
Year of construction : …
Ex nA II T6 to T790
IECEx LCI 10.0014X
 
Approved for issue on behalf of the IECEx
Certification Body:		Marc Gillaux

 
Position:Certification Director


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
Laboratoire Central des Industries Electriques (LCIE)
33 Avenue du General Leclerc
FR-92260 Fontenay-aux-Roses
France


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx LCI 10.0014X
 
Date of Issue:2010-07-20Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
VIBRO-METER SA
Route de Moncor 4
1701 FRIBOURG
Switzerland


 
 Additional Manufacturing location(s):
VIBRO METER
Route de Moncor 4
1701 FRIBOURG
Switzerland
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-15 : 2005-03
Edition: 3		Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
FR/LCI/ExTR10.0016/00


Quality Assessment Report:

FR/LCI/QAR06.0006/01


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx LCI 10.0014X
 
Date of Issue:2010-07-20Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 
This equipment is composed of an electromechanical transducer which delivers to an electrical load, connected to its terminal, a signal related to the measurement performed.

Specific parameters:

U ≤ 30V, I ≤ 130mA, P≤0.8 W

 

 

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

Operating ambient temperature : -200°C to +780°C

Temperature classification in function of the operating temperature :

T6 at Tamb. + 80°C; T5 at Tamb. + 95°C

T4 at Tamb. + 130°C; T3 at Tamb. + 195°C

T2 at Tamb. + 290°C; T1 atTamb. + 440°C

T790 at Tamb. + 780°C

 







Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.