IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx PTB 11.0021X issue No.: 0
 
Status:
Current
 
Date of Issue:2011-04-01Page 1 of 4
 
 
Applicant:
Pepperl+Fuchs GmbH
Lilienthalstrasse 200
68307 Mannheim
Germany
Equipment:Cuboidal inductive proximity sensors
 
Optional accessory:
 
Type of Protection:Intrinsic Safety

 Marking: Ex ia IIC T6 Ga
Ex ib IIC T6
Ex ia I
 
 
Approved for issue on behalf of the IECEx
Certification Body:
Dr.-Ing. U. Johannsmeyer

 
Position:Head of Department "Intrinsic Safety and Safety of Systems"


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
Physikalisch-Technische Bundesanstalt (PTB)
Bundesallee 100
38116 Braunschweig
Germany


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 11.0021X
 
Date of Issue:2011-04-01Issue No.: 0
 
Page 2 of 4
  
Manufacturer:
Pepperl+Fuchs GmbH
Lilienthalstrasse 200
68307 Mannheim
Germany


 
Additional Manufacturing location(s):
Pepperl+Fuchs PTE Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Singapore
Pepperl + Fuchs GmbH
Lilienthalstrasse 200
68307 Mannheim
Germany

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-26 : 2006
Edition: 2
Explosive atmospheres - Part 26: Equipment with equipment protection level (EPL) Ga
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

DE/PTB/ExTR11.0036/00


Quality Assessment Report:

DE/PTB/QAR06.0007/02DE/PTB/QAR06.0008/02


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 11.0021X
 
Date of Issue:2011-04-01Issue No.: 0
 
Page 3 of 4
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The cuboidal inductive proximity sensors of types FJ... NJ..., NB... and NC are used to convert mechanical displacements into an electrical signal.  

The sensors are supplied from an intrinsically safe circuit and they are suitable to be used in hazardous areas of group I and group II.
The area classification of the inductive sensor depends on the level of protection of the intrinsically safe circuits the sensors are connected to.

For further information reference is made to the annex.

 



 SPECIFIC CONDITIONS OF USE:   YES as shown below:
 
 

For special conditions, reference is made to the annex.

 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 11.0021X
 
Date of Issue:2011-04-01Issue No.: 0
 
Page 4 of 4
 
 Additional information:
 
 
For electrical and thermal specifications for the individual types of cuboidal inductive proximity sensors, reference is made to the annex.
 
 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.