IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx TSA 07.0029 issue No.: 3
 
Status:
Current
 
Date of Issue:2016-11-16Page 1 of 4
 
 
Applicant:
Pepperl+Fuchs GmbH
Lilienthalstraβe 200
68307 MANNHEIM
Germany
Equipment:GOVAN brand - F7 Range of Junction Boxes, Control Stations and Specialised Equipment
 
Optional accessory:
 
Type of Protection:Ex d / Ex tD

 Marking: TYPE ....
Ex d IIB T6 IP66
Ex d IIB T6 IP66 - 20 °C ≤ Ta ≤ + 55 °C or
Ex d IIB T6 IP66 - 20 °C ≤ Ta ≤ + 60 °C *
Ex tD A21 T80 ˚C IP66
Ex tD A21 T 80 °C IP 66 - 20 °C ≤ Ta ≤ + 55 °C or
Ex tD A21 T 80 °C IP 66 - 20 °C ≤ Ta ≤ + 60 °C *
* Refer to Table 1 in the attached annexe
 
 
Approved for issue on behalf of the IECEx
Certification Body:
Debbie Wouters

 
Position:Acting Quality & Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
TestSafe Australia
919 Londonderry Road
Londonderry NSW 2753
Australia


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx TSA 07.0029
 
Date of Issue:2016-11-16Issue No.: 3
 
Page 2 of 4
  
Manufacturer:
Pepperl+Fuchs (Australia) Pty Ltd
131-149 Link Drive
Campbellfield VIC 3061
Australia


 
Additional Manufacturing location(s):
Pepperl+Fuchs
These products may be manufactured at any Pepperl+Fuchs facility that has been audited for the manufacture of the type of protection defined on this certificate; in addition, the site must also be listed on the Quality Assessment Reports DE/PTB/QAR06.0015/08 and DE/PTB/QAR16.0002/00 or their subsequent issues.

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 61241-0 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
IEC 61241-1 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

AU/TSA/ExTR06.0052/00AU/TSA/ExTR06.0052/01


Quality Assessment Report:

DE/PTB/QAR06.0015/08DE/PTB/QAR16.0002/00


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx TSA 07.0029
 
Date of Issue:2016-11-16Issue No.: 3
 
Page 3 of 4
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The F7 Range of Junction Boxes, Control Stations and Specialised Equipment are single body enclosures and are intended for Ex d and Ex tD applications. Enclosures may be manufactured from cast aluminium alloy, stainless steel or cast iron. Each enclosure consists of a cast body fitted with a bolted cover, which forms a flameproof flange joint. The F7 enclosures are designed for use in Group IIB gas atmospheres and practice A Zone 21 & 22 IP66.

Refer to attached annexe for details.



 SPECIFIC CONDITIONS OF USE:   NO
 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx TSA 07.0029
 
Date of Issue:2016-11-16Issue No.: 3
 
Page 4 of 4
 
 DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
 

Variations permitted by Issue 3 of this certificate:

To replace TestSafe QAR with PTB QAR and add note on additional manufacturing locations.

 
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.