IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
Certificate No.:
IECEx SIR 08.0069 issue No.:1
 
Status:
Current
 
Date of Issue:2009-03-20 Page 1 of 5


    
Applicant:
Capcis Limited
Unit 6 Long Hanborough Business Park
Long Hanborough
Witney
Oxford OX29 8LH
United Kingdom


 
Electrical Apparatus:PM 205 Potential Monitor
Optional accessory:


 
Type of Protection:Intrinsic Safety


 
Marking: [Ex ic] IIC Gc
 
Approved for issue on behalf of the IECEx
Certification Body:		C Ellaby

 
Position:Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
SIRA Certification Service
Rake Lane
Eccleston
Chester
CH4 9JN
United Kingdom


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx SIR 08.0069
 
Date of Issue:2009-03-20Issue No.: 1
 
Page 2 of 5
 
 Manufacturer:
Capcis Limited
Unit 6 Long Hanborough Business Park
Long Hanborough
Witney
Oxford
OX29 8LH
United Kingdom


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2007-10
Edition: 5		Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-11 : 2006
Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
GB/SIR/ExTR08.0103/00GB/SIR/ExTR09.0030/00


Quality Assessment Report:

GB/SIR/QAR08.0017/00


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx SIR 08.0069
 
Date of Issue:2009-03-20Issue No.: 1
 
Page 3 of 5
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The PM205 Potential Monitor is a 19 Inch 2U rack panel unit used to provide continuous monitoring of wellhead potentials and RF induction. The PM205 Monitor is intended to be installed in a non-hazardous area and provides a two-wire input/output connection to a local and remote earth point. The two-wire connection is considered to be associated apparatus with level of protection [Ex ic] IIC, due to the earth point connections being within a potentially hazardous area Zone 2.

 
There are five versions of the PM205 with three distinct differences. One version (Types B, C and E) contains an integral battery pack used for memory back-up, the other version (Type D) utilises a DC/DC power supply (externally powered) in place of the battery pack and the final version (Type A) has no DC/DC supply or battery pack fitted. The ‘Type D’ version of the PM205 in addition to the DC/DC power supply has an additional 2-pin connector and fuse holder fitted to the rear side of the panel. The other versions of the PM205 unit have minor cosmetic differences listed below:
 
Type ANo Batteries, No DC/DC supply, with a Black case
Type BBatteries, No DC/DC supply, with a Black Case
Type CBatteries, No DC/DC supply, with a Silver case
Type DDC/DC supply, No batteries, with a Black case
Type ESame as Type B, except different coloured handles
 
CONDITIONS OF CERTIFICATION: NO
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx SIR 08.0069
 
Date of Issue:2009-03-20Issue No.: 1
 
Page 4 of 5
 
 
EQUIPMENT(continued):
 
The Manufacturer shall note the following condition of manufacture:
1.Modifications to the signal PCB are required in accordance with the instructions contained on drawing T08B005F.
2.The wiring between the Wellhead and Signal PCB (J1) shall be sleeved in accordance with the instructions on drawings T08B005A or T08B005H. 
 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx SIR 08.0069
 
Date of Issue:2009-03-20Issue No.: 1
 
Page 5 of 5
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 

Issue 1 – this Issue introduced the following changes:

1.The introduction of the “types A and C through to E” version of the PM205 Potential Monitor.
2.The marking section was corrected.
 
 








Copyright © IEC-IECEx 2013 , Geneva Switzerland. All rights reserved.