IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx FMG 07.0006X issue No.:1
 
Status:
Current
 
Date of Issue:2007-10-15 Page 1 of 4


    
Applicant:
Mine Safety Appliances
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
United States of America


 
Electrical Apparatus:Ultima XL
Optional accessory:


 
Type of Protection:Construction, Test and Marking of type of protection "d", "n", and "[ib]"


 
Marking: For Calibration Options: 5
Ex d [ib] IIC T6 Ta = -40C to +60C IP66,
Ex nA [ib] IIC T6 Ta = -40C to +60C IP66,
For Calibration Options: 0
Ex d IIC T6 Ta = -40C to +60C IP66,
Ex nA IIC T6 Ta = -40C to +60C IP66
 
Approved for issue on behalf of the IECEx
Certification Body:
Robert L. Martell Jr.

 
Position:Asst. Vice President


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:
FM Approvals LLC
1151 Boston-Providence Turnpike
Norwood, MA 02062
United States of America


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2007-10-15Issue No.: 1
 
Page 2 of 4
 
 Manufacturer:
Mine Safety Appliances
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5
Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosure 'd'
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-15 : 2005-03
Edition: 3
Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus
IEC 61779-1 : 1998
Edition: 1
Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods
IEC 61779-4 : 1998
Edition: 1
Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating up to 100% lower explosive limit
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
US/FMG/ExTR07.0004/00US/FMG/ExTR07.0011/00


Quality Assessment Report:

CA/CSA/QAR06.0001/01


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2007-10-15Issue No.: 1
 
Page 3 of 4
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

Ultima XL Control Unit

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

1)      Upon installation of the Ultima XL Control unit, the label shall be permanently marked to show the type explosion protection used for the installation

2)  The Ultima XL control unit complies with IEC 61779-1 and IEC 61779-4 when connected to a Detector Head that also has been evaluated to IEC 61779-1 and IEC 61779-4. 

 

 


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx FMG 07.0006X
 
Date of Issue:2007-10-15Issue No.: 1
 
Page 4 of 4
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 
Updated to correct errors in the manufacturing locations address and correct issue edition of IEC60079-1.
 
 








Copyright © IEC-IECEx 2014 , Geneva Switzerland. All rights reserved.