IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx CES 12.0004 issue No.:0

Certificate history:

 
Status:
Current
 
Date of Issue:2012-03-15 Page 1 of 3


    
Applicant:
Pepperl + Fuchs GmbH
Lilienthalstraße 200,
68307 - Mannheim
Germany


 
Equipment:Galvanically Isolated Barrier, series KCD2-STC-Ex1.HC(.SP) and KCD2-SCD-Ex1.HC(.SP)
Optional accessory:


 
Type of Protection:Intrinsic Safety "ia"; Dust ignition protection "iD"


 
Marking:

[Ex ia Ma] I,

[Ex ia Ga] IIC,

[Ex ia Da] IIIC

 
Approved for issue on behalf of the IECEx
Certification Body:
Mr. Mirko Balaz

 
Position:Head of IECExCB


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:
CESI
Centro Elettrotecnico
Sperimentale Italiano S.p.A.
Via Rubattino 54
20134 Milano
Italy


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx CES 12.0004
 
Date of Issue:2012-03-15Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
Pepperl + Fuchs GmbH
Lilienthalstraße 200,
68307 - Mannheim
Germany


 
 Additional Manufacturing location(s):
Pepperl+Fuchs (Manufacturing) PTE LTD
18 Ayer Rajah Crescent – Singapore 139942
Singapore
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2007-10
Edition: 5
Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-26 : 2006
Edition: 2
Explosive atmospheres - Part 26: Equipment with equipment protection level (EPL) Ga
IEC 61241-11 : 2005
Edition: 1
Electrical apparatus for use in the presence of combustible dusts - Part 11: Protection by intrinsic safety 'iD'
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
IT/CES/ExTR12.0004/00


Quality Assessment Report:

DE/PTB/QAR06.0007/02DE/PTB/QAR06.0008/04


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx CES 12.0004
 
Date of Issue:2012-03-15Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The galvanically isolated barrier KC.. series (KCD2-STC-Ex1.HC,  KCD2-STC-Ex1.HC.SP,  KCD2-SCD-Ex1.HC  and  KCD2-SCD-Ex1.HC.SP) is a group of associated apparatus suitable to interface intrinsic safety apparatus placed in hazardous area.

The modules KCD2-STC-Ex1.HC(.SP) provide supply for 2 wire 4..20mA transmitters located in hazardous area (input side) and transfer the signal to the control safe area (output side) as 4..20mA current source/sink or 1..5V voltage output. Additionally the input shall also be able to measure the signal from an active current source.

The modules KCD2-SCD-Ex1.HC(.SP) transfers a 4…20 mA signal from the control safe area (input side) to the hazardous area (output side) to drive smart I/P converters, electrical valves or positioners. On both the devices, a digital SMART communication may be superimposed on the analogue values in the input or output side and may be transferred in both directions.

 

The ambient temperature may vary in a range of -20°C to + 60 °C.

 

See annex for further description and for Information about the intrinsic safety electrical parameters.

 .

 
SPECIFIC CONDITIONS OF USE: NO
 
 







Copyright © IEC-IECEx 2016 , Geneva Switzerland. All rights reserved.