IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx CES 14.0022X issue No.: 0
 
Status:
Current
 
Date of Issue:2014-07-07Page 1 of 3
 
 
Applicant:
Pepperl+Fuchs GmbH
Lilienthalstraße 200,
68307 - Mannheim
Germany
Equipment:Cable Glands series CG.AR2.., CG.CR.. and CG.AR..
 
Optional accessory:
 
Type of Protection:Flameproof enclosures ‘d’; increased safety 'e'; Dust ignition protection 't'

 Marking: Ex d IIC Gb

Ex e IIC Gb

Ex tb III C Db

IP 66/68

 
 
Approved for issue on behalf of the IECEx
Certification Body:
Mirko Balaz

 
Position:Head of IECEx CB


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
CESI
Centro Elettrotecnico
Sperimentale Italiano S.p.A.
Via Rubattino 54
20134 Milano
Italy


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx CES 14.0022X
 
Date of Issue:2014-07-07Issue No.: 0
 
Page 2 of 3
  
Manufacturer:
Pepperl+Fuchs GmbH
Lilienthalstraße 200,
68307 - Mannheim
Germany


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2011
Edition: 6.0
Explosive atmospheres - Part 0: General requirements
IEC 60079-1 : 2007-04
Edition: 6
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC 60079-31 : 2008
Edition: 1
Explosive atmospheres – Part 31: Equipment dust ignition protection by enclosure 't'
IEC 60079-7 : 2006-07
Edition: 4
Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

IT/CES/ExTR14.0022/00IT/CES/ExTR14.0023/00


Quality Assessment Report:

DE/PTB/QAR06.0007/03


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx CES 14.0022X
 
Date of Issue:2014-07-07Issue No.: 0
 
Page 3 of 3
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The series of cable gland with trademark Pepperl+Fuchs GmbH is composed by the following types.

Type CG.CR.. cable glands are designed for non-armoured cables and are comprised of a male body, lower sealing ring, pressure ring and cap. When the cap is screwed onto the male body, the pressure ring comprises the lower sealing ring onto the outer sheath of the cable and realizes the clamp.

Type CG.AR2.. cable glands are designed for steel wire armour or shielded cables and are comprised of a male body, lower sealing ring, grounding cone, swivel braid retainer, middle body, upper sealing ring and cap. When the middle body is screwed onto the male body the cable wire armour is clamped between the swivel braid retainer and the grounding cone and the lower sealing ring is compressed onto the inner sheath of the cable. Sealing of the cable outer sheath is facilitated by the upper sealing ring which is compressed onto the outer sheath when the cap is screwed onto the middle body.

Type CG.AR.. cable glands are designed for steel wire armour or shielded cables and are comprised of a male body, lower sealing ring, grounding cone, swivel braid retainer, middle body, upper sealing ring and cap. When the middle body is screwed onto the male body the cable wire armour is clamped between the swivel braid retainer and the grounding cone and the lower sealing ring is compressed onto the inner sheath of the cable. Sealing of the cable outer sheath is facilitated by the upper sealing ring which is compressed onto the outer sheath when the cap is screwed onto the middle body.

The cable glands characteristics are further described in the Annexe of this certificate.



 SPECIFIC CONDITIONS OF USE:   YES as shown below:
 
 
  • The coupling of the cable glands with the enclosures shall be made as indicated by the manufacturer in the documents annexed to this certificate in order to respect the type of protection of the electrical apparatus on which cable glands are mounted.
  • The cable glands shall be mounted at the electrical apparatus in such a way that accidental rotation and loosening will be prevented.
  • The cable glands shall be installed in such a way that the temperature at the mounting point will remain within the following service temperature ranges:
    •  -40°C up to +100°C for series CG.AR2.. and CG.CR.. cable glands with sealing rings made of Chloroprene (Neoprene);
    •  -60°C up to +130°C for series CG.AR2.. and CG.CR.. cable glands with sealing rings made of Silicon rubber.
    •  -40°C up to +80°C for series CG.AR.. cable glands with sealing rings made of Chloroprene (Neoprene);
    •  -60°C up to +100°C for series CG.AR.. cable glands with sealing rings made of Silicon rubber.
  • The type CG.AR.. cable glands are only suitable for fixed installations. The cables must be effectively clamped to prevent pulling and twisting.
  • The degree of protection IP 66/68 according to the IEC 60529 standard will be guaranteed for the cable glands if the holes into which cable glands are mounted are suitably sealed. To this scope the correct positioning of the gaskets (for cylindrical threads) or the application of sealant on the threads (for tapered threads), shall be done as indicated in the manufacturer instruction.
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.