IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx SIR 06.0030X issue No.: 0

Certificate history:

 
Status:
Current
 
Date of Issue:2008-03-31Page 1 of 3
 
 
Applicant:
Pratley Manufacturing (Pty) Limited
Jackson Street
Factoria
Krugersdorp
South Africa
Equipment:Ezee Fit Junction Boxes
 
Optional accessory:
 
Type of Protection:Increased safety and dust

 Marking: Ex e II
Ex tD A21 IP 64 T85 °C
 
 
Approved for issue on behalf of the IECEx
Certification Body:
C Ellaby

 
Position:Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
SIRA Certification Service
Rake Lane
Eccleston
Chester
CH4 9JN
United Kingdom


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 06.0030X
 
Date of Issue:2008-03-31Issue No.: 0
 
Page 2 of 3
  
Manufacturer:
Pratley Manufacturing (Pty) Limited
Jackson Street
Factoria
Krugersdorp
South Africa


 
Additional Manufacturing location(s):
Weidmüller
43 Huntingwood Drive,
Huntingwood,
NSW 2148
Australia
Weidmüller
43 Huntingwood Drive,
Huntingwood,
NSW 2148
Australia

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-7 : 2006-07
Edition: 4
Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
IEC 61241-0 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
IEC 61241-1 : 2004
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

GB/SIR/ExTR07.0127/00


Quality Assessment Report:

AU/ITA/QAR07.0004/00GB/SIR/QAR06.0042/00


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx SIR 06.0030X
 
Date of Issue:2008-03-31Issue No.: 0
 
Page 3 of 3
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 

The Ezee fit range of junction boxes are manufactured in either orange or black Polyester with a lid manufactured from the same material or in clear polycarbonate.  The junction boxes have a circular shape, with cable entry locations in the curved sidewall.  The entry points are available in various configurations.  The lid is fitted with an elastomeric gasket and is fixed to the base with four screws. 

 
See Annexe for full description and Conditions of Manufacture


 SPECIFIC CONDITIONS OF USE:   YES as shown below:
 
 

1.

When the junction boxes are manufactured from the orange polyester material or the clear polycarbonate lids are fitted, the equipment is marked: WARNING STATIC HAZARD CLEAN WITH A DAMP CLOTH. Refer to the instruction manual for further advice on how to clean the equipment safely and prevent Static charge build up.
 




Copyright © IEC-IECEx 2019 , Geneva Switzerland. All rights reserved.