IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx INE 07.0001X issue No.:3
 
Status:
Current
 
Date of Issue:2012-02-09 Page 1 of 5


    
Applicant:
Xylem Water Solutions AB
Gesällvägen 33
S-17487 Sundbyberg
Sweden


 
Electrical Apparatus:Motor for submersible pump Type series 3000
Optional accessory:


 
Type of Protection:Ex d


 
Marking: Xylem Water Solutions AB
3000 series
Ex d IIB T4 or T3 or d I
IECEx INE 07.0001X
 
Approved for issue on behalf of the IECEx
Certification Body:
Thierry HOUEIX

 
Position:Ex Certification Officer


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:
INERIS
Institut National de l'Environnement Industriel
et des Risques
BP n2
Parc Technologique ALATA
F-60550 Verneuil-En-Halatte
France


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx INE 07.0001X
 
Date of Issue:2012-02-09Issue No.: 3
 
Page 2 of 5
 
 Manufacturer:
Xylem Water Solutions AB
Gesällvägen 33
S-17487 Sundbyberg
Sweden


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-1 : 2003
Edition: 5
Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosure 'd'
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
FR/INE/ExTR07.0002/00FR/INE/ExTR07.0002/01FR/INE/ExTR07.0002/02


Quality Assessment Report:

FR/INE/QAR07.0003/03


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx INE 07.0001X
 
Date of Issue:2012-02-09Issue No.: 3
 
Page 3 of 5
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

Submersible Pump series 3000 Models are a three phase induction motor intended for connection to pumping equipment for liquids and slurries. 

Maximum depth of immersion of the motor/pump is 20 m.

The motor/pump can be operated at full load at leased half the pumphousing is submerged or according to the installation drawing. Normally closed thermal detectors fitted to each of the stator windings, and connected to the motor control circuit, disconnect supply to the motor when their temperature reaches [125 ± 6] ºC or [140 ± 6] ºC according ambient temperature and gas group application.

Connection of external circuit conductors is by means of crimp connectors located in the drive-end of the stator housing. Sealing of the cable entry is by means of an integral cable gland.

The different models are defined in the descriptive documents RS6010AE rev. 2.

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

- The thermal detectors fitted to the stator windings shall be connected into the motor control circuit in such a manner to disconnect the supply to the motor in order to prevent the Temperature Class T4 or T3 or 150°C (group I).

- The yield stress of the fastener elements of the casing must be in accordance with indications mentioned in instruction manual.

 


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx INE 07.0001X
 
Date of Issue:2012-02-09Issue No.: 3
 
Page 4 of 5
 
 
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
 

Issue 1
Instructions update

Issue 2 :
Descriptive documents update
New manufacturer name ITT Water & Wastewater AB instead of ITT FLYGT
Introduction of the variations 3127.091, 3085.190, 8212.090 and 8213.090

Issue 3:
Introduction of variation 3315.090
New manufacturer name Xylem Water Solutions AB instead ITT Water & Wastewater AB

 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx INE 07.0001X
 
Date of Issue:2012-02-09Issue No.: 3
 
Page 5 of 5
 
 
Additional information:
 

The marking has to be completed by the following:

WARNING:
DO NOT OPEN WHEN AN EXPLOSIVE GAZ ATMOSPHERE IS PRESENT
DO NOT OPEN WHEN ENERGIZED
CONNECT THERMAL PROBES

 
 








Copyright © IEC-IECEx 2014 , Geneva Switzerland. All rights reserved.