IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx UL 08.0014X issue No.:0
 
Status:
Current
 
Date of Issue:2008-09-17 Page 1 of 3


    
Applicant:
Veeder-Root Co.
125 Powder Forest Dr.
Simsbury, CT 06070
United States of America


 
Electrical Apparatus:Model 8484XX-XXX PLLD Sensor
Optional accessory:


 
Type of Protection:"ia"


 
Marking: Ga Ex ia IIA T4
 
Approved for issue on behalf of the IECEx
Certification Body:
Paul T. Kelly

 
Position:Lead Operations Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:
Underwriters Laboratories Inc (UL)
333 Pfingsten Road
Northbrook IL 60062-2096
United States of America


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx UL 08.0014X
 
Date of Issue:2008-09-17Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
Veeder-Root Co.
125 Powder Forest Dr.
Simsbury, CT 06070
United States of America


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5
Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-26 : 2006
Edition: 2
Explosive atmospheres - Part 26: Equipment with equipment protection level (EPL) Ga
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
US/UL/ExTR08.0019/00


Quality Assessment Report:

GB/BAS/QAR06.0008/01


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx UL 08.0014X
 
Date of Issue:2008-09-17Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The model 8484XX-XXX PLLD sensor is a two-wire sensor designed to convert measured pressure into a signal.  The sensor is intended for use within an Intrinsically Safe System.

 
CONDITIONS OF CERTIFICATION: YES as shown below:
 

Special Conditions of Safe Use: 

  • The device label may contain aluminum.  Care must be taken to avoid ignition hazards due to impact or friction.
  • The device must be installled as part of the Intrinsic Safety System defined in IECEx ULD08.0002X.  The descriptive system documents included with the aforementioned certificate must be followed during installation.
 







Copyright © IEC-IECEx 2014 , Geneva Switzerland. All rights reserved.