IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx PTB 09.0007U issue No.: 0
 
Status:
Current
 
Date of Issue:2009-01-13Page 1 of 4
 
 
Applicant:
Emil A. Peters GmbH & Co. KG
Westfalenstrasse 85
58636 Iserlohn
Germany
Equipment:Screw-type terminal type 210-08-*-***, 220-12-*-***, 230-12-*-***
 
Optional accessory:
 
Type of Protection:Increased Safety "e"

 Marking: Ex e II, Ex e I
 
 
Approved for issue on behalf of the IECEx
Certification Body:
Dr.-Ing. Uwe Klausmeyer

 
Position:Head of Section "Flameproof Enclosures"


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

  Certificate issued by:
Physikalisch-Technische Bundesanstalt (PTB)
Bundesallee 100
38116 Braunschweig
Germany


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 09.0007U
 
Date of Issue:2009-01-13Issue No.: 0
 
Page 2 of 4
  
Manufacturer:
Emil A. Peters GmbH & Co. KG
Westfalenstrasse 85
58636 Iserlohn
Germany


 
Additional Manufacturing location(s):

 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2004
Edition: 4.0
Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-7 : 2006-07
Edition: 4
Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

DE/PTB/ExTR09.0006/00


Quality Assessment Report:

DE/PTB/QAR06.0018/00


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 09.0007U
 
Date of Issue:2009-01-13Issue No.: 0
 
Page 3 of 4
 
Schedule
 EQUIPMENT:
Equipment and systems covered by this certificate are as follows
 
 
Description:
The screw-type terminal, types 210-08-*-***, 220-12-*-*** and 230-12-*-***, of brass consist of terminal carrier, clamping bolt of threaded pin hexnut and spring washer, cover plate as well as clamping screws with spring washers. The terminal is fixed with an internal thread to terminal stud.
The terminal is used to connect copper conductos in terminal compartments of the type of protection increased safety “e”.
Technical data
Rated voltage:    max 11.000V 
TypeRated cross section Rated current
210/08-f-08 and 210/08-f-10 max.   70 mm²   max. 180 A
210/08-h-08 and 210/08-h-10max. 120 mm² max. 254 A
220/12-p-10 and 220/12-p-12 max. 120 mm²max. 254 A
220/12-h-10 and 220/12-h-12 max. 240 mm² max. 394 A
230/12-p-12 and 230/12-p-16 max. 240mm² max. 394 A
230/12-h-12 and 230/12-h-16 max. 300mm²   max. 455 A


 SPECIFIC CONDITIONS OF USE:   NO
 
 
 


- PAGE BREAK -

IECEx Certificate
of Conformity

  
Certificate No.:IECEx PTB 09.0007U
 
Date of Issue:2009-01-13Issue No.: 0
 
Page 4 of 4
 
 EQUIPMENT(continued):
 
 
Nomenclature 
210-08-*-***
12345

 1) Number of type 210, 220 or 230
 2) threaded pin hexnut or threaded bolt
     08 = M8, 12 = M12
 3) Form of pressure plate
     f = flat
     p = prismatic
     h = half round
4) Thread of the bolt
    08 = M8, 10 = M10, 12 = M12, 16 = M16
5) Kind of pressure screw
    - = threaded pin hexnut
    i = hexagonal socket headless set screw

Notes for manufacturing and operation
When the terminals are installed in a terminal compartment the requirements according to
IEC 60079-0 must be met.
The clearances and creepage distances according to IEC 60079-7 have to be observed.

 
 




Copyright © IEC-IECEx 2018 , Geneva Switzerland. All rights reserved.