IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
an IECEx Guest User | ExCB Login

leftca_pagelinks
IECEx Certificate
of Conformity

 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com

 
Certificate No.:
IECEx EPS 11.0010 issue No.:0

Certificate history:

 
Status:
Current
 
Date of Issue:2011-11-11 Page 1 of 3


    
Applicant:
Pepperl+Fuchs GmbH
Lilienthalstr. 200, 68307 Mannheim
Germany


 
Equipment:Ex-p control unit 5000Q
Optional accessory:


 
Type of Protection:"nA", "pz", "tc"


 
Marking: Ex nA nC [pz] IIC T4 Gc
Ex nA nC [pz] IIC T6 Gc
Ex tc [p] IIIC T70°C Dc IP64
 
Approved for issue on behalf of the IECEx
Certification Body:
Achim Hänchen

 
Position:Head of Certification


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 

 Certificate issued by:
Bureau Veritas Consumer Products Services Germany GmbH
Businesspark A96
86842 Türkheim
Germany


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx EPS 11.0010
 
Date of Issue:2011-11-11Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
Pepperl+Fuchs GmbH
Lilienthalstr. 200 68307 Mannheim
Germany


 
 Additional Manufacturing location(s):
 

This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.


STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:

 
IEC 60079-0 : 2007-10
Edition: 5
Explosive atmospheres - Part 0:Equipment - General requirements
IEC 60079-15 : 2010
Edition: 4
Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
IEC 60079-2 : 2007-02
Edition: 5
Explosive Atmospheres - Part 2 Equipment protection by pressurized enclosure "p"
IEC 60079-31 : 2008
Edition: 1
Explosive atmospheres – Part 31: Equipment dust ignition protection by enclosure 't'
IEC 61241-4 : 2001
Edition: 1
Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection 'pD'
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:
DE/EPS/ExTR11.0010/00


Quality Assessment Report:

DE/PTB/QAR06.0007/02


- PAGE BREAK -

IECEx Certificate
of Conformity

 
Certificate No.:IECEx EPS 11.0010
 
Date of Issue:2011-11-11Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 
The 5000Q Controller can be used for purging time and pressure control in hazardous locations, zone 2/22. The amount of purging gas streaming into the pressurized  enclosure is controlled. After finalization of the purging time, the assemblies are switched on. Inside the enclosure the overpressure against the surrounding atmosphere is hold and controlled.
 
CONDITIONS OF CERTIFICATION: NO
 
 







Copyright © IEC-IECEx 2016 , Geneva Switzerland. All rights reserved.