IECEx CoC Home > Certified Equipment Scheme > Certificate of Conformity
important information !
IECEx Guest User | ExCB Login

IECEx Certificate
of Conformity
 
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
 
 
Certificate No.:
IECEx KEM 09.0066X issue No.:0

Certificate history:

 
Status:
Current
 
Date of Issue:2009-10-06 Page 1 of 3


    
Applicant:
Wilcoxon Research
20511 Seneca Meadows Parkway
Germantown
MD 20876
United States of America


 
Electrical Apparatus:Accelerometers
Optional accessory:


 
Type of Protection:Ex ia


 
Marking:Ga Ex ia IIC T4
 
Approved for issue on behalf of the IECEx
Certification Body:		C.G. van Es

 
Position:Certification Manager


 
Signature:
(for printed version)
 
Date:
 
 
1. This certificate and schedule may only be reproduced in full.
2. This certificate is not transferable and remains the property of the issuing body.
3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website.
 
 Certificate issued by:
KEMA Quality B.V.
Utrechtseweg 310
6812 AR Arnhem
The Netherlands


- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx KEM 09.0066X
 
Date of Issue:2009-10-06Issue No.: 0
 
Page 2 of 3
 
 Manufacturer:
Wilcoxon Research
20511 Seneca Meadows Parkway
Germantown
MD 20876
United States of America


 
 Manufacturing location(s):
 
This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended.



STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards:
 
IEC 60079-0 : 2004
Edition: 4.0		Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
IEC 60079-11 : 2006
Edition: 5		Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-26 : 2006
Edition: 2		Explosive atmospheres - Part 26: Equipment with equipment protection level (EPL) Ga
 
This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above.


 
TEST & ASSESSMENT REPORTS:
A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in

 
Test Report:

NL/KEM/ExTR09.0067/00

Quality Assessment Report:

GB/SIR/QAR09.0011/00



- PAGE BREAK -

IECEx Certificate
of Conformity
 
Certificate No.:IECEx KEM 09.0066X
 
Date of Issue:2009-10-06Issue No.: 0
 
Page 3 of 3
 
 
Schedule
 
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
 

The Accelerometers Type 780A-IS, 786A-IS, 786F-IS, 786T-IS, 787A-IS, 787A-M8-IS, CMSS780A-IS, CMSS786A-IS, CMSS786F-IS, CMSS786T-IS, CMSS787A-IS and CMSS787A-M8-IS are used for vibration monitoring.
The sensor converts mechanical forces (e.g. vibrations) of the equipment to which it is mounted into an electrical signal and converts this into a modulated voltage output signal.
The accelerometers, types 786T-IS and CMSS786T-IS also measure the temperature of the equipment and convert this into a modulated voltage output signal.

Ambient temperature range -50 °C to +120 °C.

Supply and output circuit (power/signal and common):
in type of protection intrinsic safety Ex ia IIC, only for connection to a certified intrinsically safe circuit, with the following maximum values:
Ui = 28 V; Ii = 93 mA; Pi = 650 mW; Ci = See table below; Li = 0 mH.

For models 786T-IS and CMSS786T-IS:Supply and output circuits (power/signal, temperature sense and common):
in type of protection intrinsic safety Ex ia IIC, only for connection to a certified intrinsically safe circuit, with the following maximum values:
Ui = 28 V; Ii = 93 mA; Pi = 650 mW; Ci = See table below; Li = 0 mH.

 

780A-IS, 786A-IS, 787A-IS, 787A-M8-IS, CMSS780A-IS, CMSS786A-IS, CMSS787A-IS and CMSS787A-M8-IS786F-IS and CMSS786F-IS 786T-IS and CMSS786T-IS
Ci58  nF62 nFfixed cable included76  nF
 
CONDITIONS OF CERTIFICATION: YES as shown below:
 
For applications in explosive atmospheres caused by gases, vapours or mists and where the use of apparatus with equipment protection level (EPL) Ga is required, electrostatic charges on the cable and non-metallic parts of the enclosure shall be avoided. The ambient temperature range for these applications is -40 °C to +80 °C.
 







Copyright © IEC-IECEx 2010 , Geneva Switzerland. All rights reserved.